Manual h7cx

Next Page. Set the tachometer input mode from the function setting mode to switch to the tachometer function. The functions that are provided depend on the model. Check detailed specifications before ordering. You can change the color of the Front Panel when mounting the Counter. The Counter is shipped with a black N1. Soft Cover Do not use the output from an inverter as the power supply. Pulse measurement method Periodic measurement Pulse width measurement Page 10 OUT: Two-stage Up Keys 3.

Displayed only when the configuration selection Down Keys mode is not tachometer mode. Reference value Page 12 Replacement Front Panels. Page Operating Procedures Refer to page page Refer to page page 35 for information on switching models. Also, when settings are changed, the counter is reset present value initialized and output turned OFF on returning to run mode.

Page 19 Timer to indicate that the output ON count If the forecast set value is greater than or equal to the set value, the alarm value was exceeded. Refer to Self-diagnostic Function on page page 36 for information on the e3 display.

U Key only for 6-digit models. Page 21 See note 2. See note 2. When using a 2-stage model as a 1-stage preset counter, The one-shot output time can be set in the range 0. Page 23 5. If there is power failure while output is ON, output will turn ON again when the power supply has recovered. For one-shot output, output will turn ON again for the duration of the output time setting once the power supply has recovered. Page 24 3.

Page 25 6-digit models. Note: 1. Counting is not possible for CP1 during reset 1 input. CP2 will not be affected. The dual count value will be calculated based on a CP1 present value of 0.

Counting is not possible for CP2 during reset 2 input. CP1 will not be affected. The dual count value will be calculated based on a CP2 present value of 0. Note: 5. Note 1: Displayed for output modes other than D, L, and H. Note 7: The displays for 4-digit models are shown inside. For details on the operation of the input modes, refer to Input Modes and Present Value on page When using as a dual counter, select either ADD addition or SUB subtraction as the calculation method for the dual count value.

Set the way that control output for the present value is output. The output modes that can be set vary with the model. Set the one-shot output time 0. Output times other than 0. When using as a 2-stage counter or batch counter, set the one-shot output time 0. When using as a 2-stage counter, set the one-shot output time 0. One-shot output can be used only when D, L, or H is selected as the output mode.

If the output time is set to 0. HOLD cannot be set when the output mode is K If contacts are used for input signals, set the counting speed to 30 Hz. Processing to eliminate chattering is performed for this setting. Reset Input Signal Width iflt Setting possible using. If contacts are used for input signals, set the counting speed to 20 ms. Pulses input to the counter are converted according to the specified prescale value.

Setting range: 0. Example: To display the feed distance for systems that output 25 pulses for a feed length of 0. Set the decimal point position to 2 decimal places.

Set the prescale value to 0. The same setting is used for all external inputs. For details on input connections, refer to Input Connections on page Note: When using as a 2-stage counter, this is the status of output 2. When using H7CX-AU models as a 2-stage counter, the output can be flexibly allocated to either stage 1 or 2. Transistor output can be allocated to SV1 and contact output for SV2 or vice verse, as in the following table. Welcome to ManualMachine.

We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Config- urability varies with model. Contents Model Number Structure External connection None: Screw terminals pin socket 2. Stage setting None: 1-stage setting U: Factory-set to 1-stage setting W: Factory-set to 2-stage setting.

Output type None: Contact output or contact and transistor in combination S: Transistor output 5. Y92F Waterproof Packing See note 1. PV Voltage input High logic level: 4. Key protection Yes Prescaling function Yes 0. Input mode: command, individual, or quadrature; output mode: K-2, D, or L. Display See note 2. Electrical: , operations min. Weight Approx. Increment signals can be input.

The reset indicator is lit during reset input. Counting for CP1 input cannot be performed during reset 1 input. The reset indicator is lit during reset 1 input. See note 2. Holds the total count value at 0 during total reset input. Holds the batch count value at 0 during reset 2 input. Counting for CP2 input cannot be performed during reset 2 input. CP2 input is not available. Reset 1, Reset 2 Holds the measurement value and outputs. Reset 2 input is not available.

The reset indicator is lit during hold. Terminals 1 and 6 are connected internally. Contact input Use contact which can adequately switch 5 mA at 10 V. Maximum applicable voltage: 30 VDC max. Input resistance: Approx. Applicable Two-wire Sensor Leakage current: 1. Switching capacity: 5 mA min. Residual voltage: 3 VDC max. E Batch Indicator Lit when the batch count value is displayed. J Reset Key The operation of the reset function depends on the configuration selected as shown in the table below.

Tachometer Maintains the measured value and outputs hold function. Note: Can be used as a 2-stage counter. In this case, each output can be flexibly allocated to either stage 1 or 2. Note: 1. Supplied with screw-terminal models i. Minimum reset input signal width: 1 or 20 ms selectable , common setting for all inputs. External, manual, and automatic reset internal according to C, R, P, and Q mode operation. Control output is turned OFF and no input is accepted during sensor waiting time.

Only when the following modes are selected. See Life-test Curve on page A waterproof packing is necessary to ensure IP66 waterproofing between the H7CX and installation panel. Reference: A current of 0. In both cases, a life of , operations can be expected. Display circuit. Resets present value and outputs OUT2 when using the batch counter.

See note 1. Outputs take place according to designated output mode when corresponding preset is reached. The reset indicator will not be lit when the total reset or reset 2 input is ON. Outputs signals according to the specified output mode when a set value is reached. Total reset. Note: Do not connect unused terminals as relay terminals.

Reset 1. Reset 2. Do not connect unused terminals as relay terminals. Note: Each output can be flexibly allocated to either stage 1 or 2 by setting in function selection mode.

Note: Each output can be flexibly allocated to either stage 1 or 2 in function selection mode. Note: The circuit shown above is for no-voltage input NPN input. The inputs of the H7CX are no-voltage short-circuit or open inputs or voltage inputs. CP2 input. CP1 input. Leakage current Switching capacity:5 mA min.

Residual voltage:3 VDC max. Operating voltage VDC. The operation of the reset function depends on the configuration selected as shown in the table below.

K Up Keys: 1 to 4 6-digit models: 1 to 6. Note: All units are in millimeters unless otherwise indicated. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?